Why do the dispensing tools of my ep Motion need to be calibrated?

The dispensing tools are precision devices. Servicing and calibration at regular intervals ensure a consistently high precision of the results. We provide documentation in support for GLP to assist you.

What is IQ or OQ and what do I need them for?

Installation and operational qualification; the IQ documents that the device has been delivered and installed correctly. The OQ checks the correct functioning of a device. IQ/OQ ensure that your quality management requirements are met and that your device operates properly and in accordance with the manufacturer’s specifications.

What types of training or online training do you offer to enable me to improve my skills?

Please visit the Eppendorf webpage about the Eppendorf Training Center ( https://www.eppendorf.com/training or contact your local Eppendorf Service for further information and a quotation.

How often does the OQ need to be carried out for an ep Motion ?

The company is responsible for technical checks of devices. Eppendorf recommends regular device qualifications depending on the intensity of use, however, they should be carried out at least once a year.

How often do dispensing tools need to be calibrated?

As part of his test equipment monitoring process, the operator determines the frequency of the calibration as well as the quantity of the testing volume and the number of measurements for each testing volume. This may vary depending on how often the device is used, by how many operators it is used, the aggressivity of the liquids used and the maximum permissible errors defined by the operator. The dispensing tools of your device will display after 200,000 runs that an inspection is recommended. However, there should be at least 1 calibration per year.

Why should I have my ep Motion serviced at regular intervals?

To ensure the optimum performance and precision of your device. This also enables the early detection of any defects which can then be corrected easily. Only precise and accurate devices ensure successful liquid transfers!

Does a service carried out by Eppendorf meet the GMP requirement?

Eppendorf offers global certification services which comply with FDA 21 CFR Part 11, EU GMP Annex 11, GLP and GAMP ® 5 to ensure a consistent, standardized operation. We also enable an uncomplicated validation from the implementation to the shutdown by providing support for the installation und operational qualifications (IQ/OQ) of the device and with the software. The entire qualification is documented in detail and the operator’s personnel is qualified and certified in intensive training sessions.

Who is my local service contact?

Please contact your local Eppendorf Service Team. You find the contact data on our homepage ( www.eppendorf.com ) or in the information materials.

What types of service programs are available for ep Motion ?

The available service programs can be found under the respective instrument in the Service & Support / Maintenance and Certification Services section.

What do you need to look out for before carrying out a service?

The device needs to be decontaminated first. The device must be freely accessible and all samples removed from the device.

Why can the dispending tool be calibrated without the user unit ?

The ep Motion dispensing tool is calibrated with the help of the ep Motion Tool Holder. The electronic parameter to control the tools of the ep Motion are always the same in all ep Motion units. Therefore all ep Motion dispensing tool can be calibrated on different units than the user unit. The only exceptions are the TS10 and TM10 dispensing tool. They can only be calibrated with units controlled by epBlue Version 40.5.

How much are the different ep Motion service programs?

The costs depend on the model and service that is performed. Please contact your local Eppendorf Service.

Which consumables should be replaced at regular intervals?

All three XYZ flex cables should be replaced at least once per year if the machine is used daily.

How often does my ep Motion need to be serviced?

The need for service depends on how intensively the device is used and if you are working in a regulated field with special service demands. However, we recommend to have it serviced at least once a year.

text.skipToContent text.skipToNavigation

DE | EUR

No results found

Search Suggestions

Product Families

Show all Product Families ()

Article

Show all Articles ()

Content

Show all Content ()

epMotion^® Height Adapters

Height adapters speed up work on automated liquid handling systems

Product Information

For the optimization of workflow processes, it may become necessary to adjust the heights of all the vessels used (tip racks, plates and reservoir racks) to the same level in order to minimize vertical traveling distances as well as save time. Our height adapters are the ideal solution that will bring your work table to one level.

Show more Product Information

You will find additional download material at the bottom of this page

Products (3)

3 Products

More Product Details ...

Quantity

Check stock

Catalog no. 5075751003

Price

460,00 €

Inquire

More Product Details ...

Quantity

Check stock

Catalog no. 5075752000

Price

460,00 €

Inquire

More Product Details ...

Quantity

Check stock

Catalog no. 5075755009

Price

460,00 €

Inquire

Show more Products

Added to Your Cart

Product Information

Features

Downloads: epMotion^® Height Adapters

Read Less

Your session will expire soon

Minutes

Seconds

epMotion^® Height Adapters

Product Information

Product Information

Features

Downloads: epMotion^® Height Adapters

Your session will expire soon

Minutes

Seconds

You are about to leave this site.

epMotion® Height Adapters

Height adapters for epMotion

Product Information

Products (3)

Product Information

Features

Downloads: epMotion® Height Adapters

FAQs(14)

epMotion^® Height Adapters

Downloads: epMotion^® Height Adapters