Software/Firmware revisions are made available at no charge through this web page so that all users can benefit from the latest performance enhancements.
The easy upgrade procedure takes only a few minutes to perform.
Software/Firmware revisions are made available at no charge through this web page so that all users can benefit from the latest performance enhancements.
The easy upgrade procedure takes only a few minutes to perform.
Date/File/Version | Description of Changes |
---|---|
30-Jan-2019 Update_M1372_B.00.zip Version Analog B.00 | Analog I/O software revision B.00 includes the ability to recognize and control up to 8 Analog I/O modules from a single installed version, and addresses previous issues with communication loss. |
NOTE: This update is required for any current customer planning to use BioCommand witha BioFlo® 320. The enhancements made to are specific to the TCP/Modbus protocol used in the BioFlo® 320. There is no change to the functionality of BioCommand for all other New Brunswick™ bioprocess equipment.
NOTE: It is recommended that all customers update their software, however, customers running Revision C BioCommand software packages with all other New Brunswick™ bioprocess equipment are not required to install the update.
WARNING: Do not attempt to install this update on BioCommand® Batch Control Plus installations. Database files are not compatible and may result in loss of data. For BioCommand® Batch Control Plus updates, please contact your local sales/service representative.
Date/File/Version | Description of Changes |
---|---|
30-Jan-2019 Update_BC_TT_BC_Version_D.zip Version D | Revision D includes the following enhancements: • Communication over TCP/Modbus protocol • Addition of proportional and integral (P&I) values to programming section • Addition of control mode selection to programming section • Addition of P&I, deadband, and totalizer values to Batch Summary, Datalog, and Reports |
Date/File/Version | Description of Changes |
---|---|
22-May-2013 M1291-1252 Rev C.00 - Update.zip Version C | The updated version of BioCommand SFI allows for the correct interperation of values when used with European operating systems while continuing to report values on US operating systems. This improved version also allows BioCommand SFI to be used with up to 2 each New Brunswick S41i CO2 Incubator Shakers. It trends and archieves critical data including temperature, speed and gas concentration but does not provide batch control. |
NOTE: This update is required for any current customer planning to use BioCommand witha BioFlo® 320. The enhancements made to are specific to the TCP/Modbus protocol used in the BioFlo® 320. There is no change to the functionality of BioCommand for all other New Brunswick™ bioprocess equipment.
NOTE: It is recommended that all customers update their software, however, customers running Revision C BioCommand software packages with all other New Brunswick™ bioprocess equipment are not required to install the update.
WARNING: Do not attempt to install this update on BioCommand® Batch Control Plus installations. Database files are not compatible and may result in loss of data. For BioCommand® Batch Control Plus updates, please contact your local sales/service representative.
Date/File/Version | Description of Changes |
---|---|
30-Jan-2019 Update_BC_TT_BC_Version_D.zip Version D | Revision D includes the following enhancements: • Communication over TCP/Modbus protocol • Addition of proportional and integral (P&I) values to programming section • Addition of control mode selection to programming section • Addition of P&I, deadband, and totalizer values to Batch Summary, Datalog, and Reports |
Date/File/Version | Description of Changes |
---|---|
30-Jan-2019 | Software revision 05.01 incorporates the following solutions/additions to improve the performance of your bioprocess controller: • Update for Corporate Identity |
Date/File/Version | Description of Changes |
---|---|
31-Jan-2019 | Software revision 02.07 incorporates the following solutions/additions to improve the performance of your bioprocess controller: NOTE: This is a critical software update as IP addressing issues may lead to board failure, requiring board replacement • Resolves Static IP addressing issues if network settings contains an IPv6 IP address or invalid Netmask. |
Date/File/Version | Description of Changes |
---|---|
30-Jan-2019 Update_M1297 _12.04.zip Version 12.04 | Software revision 12.04 incorporates the following solutions / additions to improve the performance of your bioprocess controller:
|
Date/File/Version | Description of Changes |
---|---|
28-Oct-2019 Update_1379_02.07.0010.zip | Software revision 02.07 incorporates the following solutions/additions to improve the performance of your bioprocess controller:
|
Date/File/Version | Description of Changes |
---|---|
30-Jan-2019 Version 02.02.0006 | Software revision 02.02.0006 incorporates the following solutions/additions to improve the performance of your bioprocess system: |
Date/File/Version | Description of Changes |
---|---|
28-Oct-2019 | Software revision 02.05 incorporates the following solutions/additions to improve the performance of your bioprocess controller:
|
NOTE: This update is specific to 1st generation CelliGen BLU cabinets. Please check the model of your CelliGen BLU cabinet. If your CelliGen BLU model number begins with the prefix "M1363", please follow the steps on this page to complete your update. If your CelliGen BLU model number begins with the prefix "M1374", please see the update CelliGen BLU (2nd Generation)
Date/File/Version | Description of Changes |
---|---|
30-Jan-2019 Update_M1363_C.00.zip | CelliGen®BLU (first generation only) software revision C.00 provides the following resolutions and/or enhancements: • Manual gas mixing total percent correction |
NOTE: This update is specific to 2nd generation CelliGen BLU cabinets. Please check the model of your CelliGen BLU cabinet. If your CelliGen BLU model number begins with the prefix "M1374", please follow the steps on this page to complete your update. If your CelliGen BLU model number begins with the prefix "M1363", please see the update for CelliGen BLU (1st Generation).
Date/File/Version | Description of Changes |
---|---|
30-Jan-2019 | Software revision 02.02 incorporates the following solutions / additions to improve the performance of your bioprocess controller: Update for Corporate Identity Update default Proportional and Integral values for pH loop |
Date/File/Version | Description of Changes |
---|---|
30-Jan-2019 M1295 RS232 Device Interface Kit Rev B.00 - Update.zip Version B | Update resolves communication errors with PC COM ports. |
Date/File/Version | Description of Changes |
---|---|
19-Nov-2018 3.0.2 - ThermoMixer Autoupdate.zip | Software version 3.0.0 enables the Eppendorf ThermoMixer® C, ThermoMixer® F, and ThermoStat® C to control the SmartExtender 1.5 mL Moreover, the software version 3.0.0 allows temperature control duration between 5 s up to 99:30 h. |