Why do you recommend mixing at max. 2,000 rpm when using the tube holders?

Because of their high balance point and their maximum capacity (e.g., Tube Holder 1.5/2.0 ml), the imbalance detector might be activated at mixing frequencies above 2,000 rpm. This automatically reduces the mixing frequency to prevent the tubes and the tube holder from jumping out of the Universal Holder.

At which speed is vortexing possible?

You can use either the touch vortexer at 3,500 rpm, or vortexing can be set to continuous by setting the mixing rate and mixing period to a range between 300 and 3,000 rpm. In continuous vortexing mode vortexing at mixing frequencies between 2,000 rpm and 3,000 rpm may occasionally activate the automatic imbalance detector.

During continuous vortexing the speed dropped suddenly and "TOO FAST" appeared in the display, why?

MixMate's automatic imbalance sensor, which prevents plates and tubes from jumping out during the mixing process, may be occasionally initiated during continuous vortexing at speeds between 2,000 and 3,000 rpm. Safety when mixing plates is of utmost priority, therefore this feature cannot be technically altered.

MixMate suddenly reduced my mixing rate and "TOO FAST" appeared in the display, why?

MixMate's automatic imbalance sensor determined irregularities during the mixing process and, for safety reasons reduced the mixing rate to prevent the plate or tubes from jumping out of the holder. This may be attributed to one or more of the following This may be attributed to one or more of the following reasons: - Plates are not correctly seated, or they do not comply with the SBS format - tube holders have not been properly inserted, or they have been unequally loaded - the mixing rate has been set too high for the weight of the mixing material - In continuous vortexing mode vortexing at frequencies between 2,000 rpm and 3,000 rpm may occasionally activate the automatic imbalance detector.

My tube holders rattle when I use MixMate, why?

The tube holders may not have been properly inserted into the Universal Holder. Check to make sure that the lugs on the rear side of the tube holder are properly latched into the holes of the Universal Holder.

I would like to check the accuracy of the mixing rate. How do I do it?

We recommend using a calibrated stroboscope or a calibrated flash lamp with a systematic error of <- 0.1 %.

Can MixMate be used in automated systems or integrate into an automated pipetting system?

No, because MixMate is not equipped with an interface.

Can I program MixMate to run different mixing steps sequentially?

No. MixMate is not programmable.

Is MixMate able to heat or cool samples?

No, MixMate is a mixing device. For tempering (heating, cooling) of plates or tubes we recommend the Eppendorf Thermomixers or Eppendorf ThermoStat plus.

Can MixMate be operated in an incubator at 37°C?

Yes, MixMate can be operated at ambient temperatures of 2 – 40°C and a relative air humidity of 10 – 75 %.

Can MixMate be operated in a cold room at 4°C?

Yes, MixMate can be operated at ambient temperatures of 2 – 40°C and a relative air humidity of 10 – 75 %. A note of caution: Condensate formation may damage electronic components! After using MixMate in a cold room, wait one hour before reconnecting the device to the power supply.

Will using MixMate heat my sample?

MixMate's ventilation concept enables the installed fans to take in cool air from above while dissipating the heated air from the bottom of the device. Thus, waste heat does not come into contact with the sample material. Internal tests have shown that even after 3 hours of continuous operation at 3,000 rpm, a sample will be heated by no more than max. 2-3°C.

Can I switch off the acoustic signal during operation, or at least turn down the volume?

You can either deactivate the signal tone (VOL0) or choose between three different volume settings (VOL1 – VOL3). To do so use the arrow key to select "M-1 VOL" in the menu. After pressing the "Menu/Enter" button you can edit the settings.

Can I use the Eppendorf IsoRack (of the IsoTherm-System) on MixMate?

Yes, the Eppendorf IsoRacks for 1.5/2.0 ml and 0.5 ml micro test tubes can be used in combination with the 1.5/2.0 ml or 0.5 ml tube holders.

Can I control MixMate using a computer?

No. MixMate is not equipped with an interface, therefore it cannot be controlled by external devices.

Can I order the tube holders individually as replacement parts?

Yes, to do so please contact your local Eppendorf dealer. The catalog numbers for the tube holders are: - Tube Holder PCR 96: 5353 040.113 (Eppendorf North America: 022674005) - Tube Holder 0.5 ml: 5353 040.121 (Eppendorf North America: 022674021) - Tube Holder 1.5/2.0 ml: 5353 040.130 (Eppendorf North America: 022674048)

Can I order the vortex mat as a replacement part?

Yes, to do so please contact your local Eppendorf dealer. The order number for the vortex mat is: 5353 863.004 (Eppendorf North America: 022674105)

Can I vortex several micro test tubes simultaneously?

Yes, during continuous vortexing: Set the required mixing rate (300 – 3,000 rpm) and mixing period (15 s – 99.5 h; continuous) using the keypad, and then start the vortexing process using the "start/stop" key. You can use the complete rubber mat in the MixMate's Universal Holder for vortexing. Touch-vortexing mode is inactivated during continuous vortexing.

Can 6-, 12-, 24-, or 48-well cell culture plates be used on MixMate?

Yes, cell culture plates can be used on MixMate – as long as they comply with the SBS Standard for Microplates, and they can be mixed at a minimum mixing rate of 300 rpm.

Can semi-skirted PCR plates be used with MixMate?

Yes, with the aid of the Tube Holder PCR 96, semi-skirted PCR plates can also be fitted onto MixMate.

Can unskirted PCR plates be used with MixMate?

Yes, with the aid of the Tube Holder PCR 96, unskirted PCR plates can also be used.

During mixing of my 384-well PCR plate air-bubbles have formed at the bottom of the wells. How can I prevent this?

The applied mixing frequency is too high for your experimental setup. To determine the optimal mixing frequency for your experiment please proceed as follows: Reduce the mixing frequency by approx. 500 rpm and insert a PCR plate with samples at the bottom of the wells (no bubbles). Increase the mixing frequency gradually until bubbles are formed. The optimal mixing speed is 50 – 100 rpm below this value.

Is the mixing rate reduced when MixMate is fully loaded?

No. Even at maximum capacity, the mixing rate is not affected.

Are MixMate and the tube holders resistant to UV radiation?

They have a limited resistance against UV light. Whereas the proportion of UV light within daylight does not harm the material, exposure to special UV lamps will damage the material and lead to discoloration. Therefore, we do not recommend disinfecting MixMate.

I understand that skirted 96-well PCR plates can be directly inserted onto MixMate. But can I also use the Tube Holder PCR 96 for this?

Yes, 96-well skirted PCR plates can be mixed both directly – using MixMate's Universal Holder – or with the aid of the Tube Holder PCR 96.

Despite using the soft keys, lid wetting has occurred, why?

The risk of lid wetting depends on factors such as tube size, chosen mixing speed, filling volume and the properties of the sample material (e.g., buffer composition, viscosity, density). To easily configure your optimum mixing parameters, despite this multitude of variables, MixMate is equipped with preprogrammed soft keys for fast and controlled mixing in the majority of standard applications. If the parameters for your particular application are not ideal, then use the soft keys as a basis for determining the optimum conditions for your applications.

Despite the imbalance sensor, my plate suddenly jumps out of MixMate, why?

Possible reasons: - The plate does not comply with the SBS Standard for Microplates. - The plate is extremely worn or deformed.

What does the term 2DMix-Control technology describe/stand for?

2DMix-Control technology describes MixMate’s ability to mix small sample volumes from 5 µl to 2 ml in various plate and tube formats quickly and in a controlled manner. It has to do with the way MixMate’s features for efficient and controlled mixing interplay, resulting in: - Generation of sufficient mixing energy: MixMate’s orbital mixing movement at a high mixing speed (max. 3,000 rpm) and a relatively large mixing radius (1.5 mm) generates enough mixing energy (analogous to g-force in centrifuges) to mix even the smallest volumes efficiently. - Minimized loss of mixing energy: During MixMate’s development, special attention was paid to reducing inherent vibration. Its smooth operation combined with its reliable stability ensures that all the mixing energy is available for mixing and not wasted through transmission of vibrations to the device or its surroundings. - Controlled transmission of energy from the device to the sample: Minimizing vertical movements enable a plane, 2-dimensional (2D) mixing stroke. This, in conjunction with the reliable plate and tube holders, prevents uncontrolled chaotic movements and allows all formats to be held securely, even at high mixing frequencies.

What other special features does MixMate have in addition to 2DMix-Control technology?

In addition to the 2DMix-Control technology, which enables fast and controlled mixing of small volumes from 5 µl to 2 ml, MixMate also provides these safety & convenience benefits: - 3-in-1 format: Mixes plates, tubes and vortexes - Soft keys, make it easier to configure the optimum mixing parameters - Digital display for maximum reproducibility of experimental conditions - Automatic imbalance detection, prevents plates from jumping out - Remarkably silent: noise level <50 dB(A)

What is the SBS Standard for Microplates?

The Society for Biomolecular Sciences ( SBS ) collaborates with other institutions to develop standards for micro test plates – the objective is to standard the various formats for easier automation. For use with MixMate the footprint of plates should meet the following specifications: - Rectangular plate - Length = 127.76 mm +/- 0.5 mm; width = 85.48 mm +/- 0.5 mm - The footprint must be continuos and uninterrupted around the base of the plate.

Which soft keys should I use for deepwell plates?

Due to the fact that deepwell plates accommodate a variety of different vessel geometries (based on height of plate, maximum fill volume, shape of the wells) and can be used with different fill volumes, it is not possible to make a general statement about the most suitable soft keys or the ideal mixing parameters for them. Basic rules are: - DWP (96-well) with 2,000 µl, 1,000 µl and 500 µl filling volumes: - With most solutions try setting a mixing rate of 1,400 rpm (soft key 1.5/2.0), as many of these DWP have a mixing rate similar to 1.5 ml and 2.0 ml micro test tubes. - For resuspension of bacteria pellets try a mixing rate of 2,000 rpm, approx. 1 min. - DWP (384-well) - Try mixing at 2,000 rpm; when using the 384 soft key visually check the process to ensure the mixing period is sufficient for complete mixing.

Which tubes can I mix with MixMate?

MixMate can be used to mix 0.2 ml PCR tubes, and PCR strips as well as 0.5 ml, 1.5 ml and 2.0 ml micro test tubes (using the tube holders included in the delivery package).

Which norms and standards are fulfilled by MixMate?

The MixMate fulfills the following directives and standards (as of April 2006): 73/23/EWG, EN 61010-1, EN 61010-2-051, 89/336/EWG, EN 55011/B, EN 61000-6-1, EN 61000-3-2, EN 61000-6-6, EN 61326, 98/79/EG, EN 14971, EN 591, EN 980)

What are the ideal parameters for resuspension of bacteria pellets?

The compact bacteria pellets require a relatively high mixing energy for efficient resuspension. Internal tests have shown that bacteria pellets with buffer volumes like those used for plasmid isolation undergo resuspension within max. 1 min at 2,000 rpm – without any lid wetting.

Which plates can be used on MixMate?

All plate formats that comply with the SBS Standard for Microplates, for example: MTPs (up to 384-well), 96- and 384-well PCR plates (skirted, semi-skirted, unskirted), deepwell plates (up to 384-well), cell culture plates (6-, 12-, 24-, 48-, 96- and 384-wells).

For which plates/tubes have the soft keys been optimized?

- 384 (15 s/2,000 rpm): MTP (384-well) - PCR 384 (15 s/2,600 rpm): PCR plates (384-well) - 96 (30 s/1,000 rpm): MTP (96-well) - PCR 96/0.5 (30 s/1,650 rpm): PCR plates (96-well), 0.2 PCR tubes and PCR strips, 0.5 ml micro test tubes - 1.5/2.0 (1 min/1,400 rpm): 1.5 and 2.0 ml micro test tubes.

If fluid is inadvertently spilled on MixMate, should I worry about it entering the device?

MixMate is designed such that small quantities of fluid cannot penetrate the device. If fluid is spilled on it, disconnect the mains plug and clean the device thoroughly; follow the instructions in the Operating Manual accordingly.

How can I disinfect MixMate and its tube holders?

To avoid a short-circuit follow these safety instructions: - Before cleaning or disinfecting the housing, switch off MixMate and disconnect the mains plug/power cord. - Do not allow any liquids to penetrate the inside of the housing. - Only reconnect the the device to the power supply and turn it back on when it is completely dry. To disinfect MixMate we recommend using alcohol (e.g., ethanol, isopropanol) or alcohol-containing disinfectants. Do not use UV radiation, as this will damage the plastics.)

How can I remove DNA contamination from MixMate and the tube holders?

Please follow the instructions within the operating manual. To avoid a short-circuit follow these safety instructions: - Before cleaning or disinfecting the housing, switch off MixMate and disconnect the mains plug/power cord. - Do not allow any liquids to penetrate the inside of the housing. - Only reconnect the device to the power supply and turn it back on when it is completely dry. If necessary, remove the Universal Holder per the operating manual instructions and wipe off DNA contamination with a moistened tissue. Change tissues repeatedly. The Universal Holder, vortex mat and tube holders should then be rinsed with running water, followed by distilled water. For stubborn DNA contamination, the different parts can be cleaned by wiping off with commercially available DNA decontamination solutions.

To which chemicals are MixMate and the tube holders resistant?

For questions regarding the resistance against chemicals, radiation and temperature please contact the Eppendorf Application Hotline (support@eppendorf.com).

How can I determine the ideal mixing parameters for my application?

We recommend dyeing the solution with the highest density or the highest viscosity with a color (e.g., Patent Blue V, Ponceau 4R), and then pipetting it as the last component on the bottom of the tube. You should try various mixing rates to determine the speed at which the sample material can be mixed quickly without any lid wetting. After several mixing periods (e.g., 5 s, 15 s, 30 s, 45 s, 1 min, 3 min) check your sample visually to ensure that the color has been completely distributed throughout. You can use the soft key settings as a reference/starting point when optimizing the mixing rate.

What does it mean when the display flashes on and off with two adjacent circles alternating with the mixing parameters?

The display flashes on and off symbolized by the two adjacent circles “oo” in order to draw your attention to the fact that the mixing period has been set to infinite.

Why does the control-LED go out when I change the parameters of a soft key?

Because the altered values no longer match the parameters assigned to that soft key the control-LED light goes out. This prevents any confusion bewteen the mixing parameters.

Why do you recommend that I mix deepwell plates at max. 2,000 rpm?

Depending on geometry and filling volume, DWPs might have a high balance point and heavy weight, respectively. Due to safety reasons, the imbalance detector may be activated at mixing frequencies above 2,000 rpm and automatically reduce the mixing frequency (to avoid plates jumping out of the Universal Holder).

How can MixMate mix samples in a controlled manner, without any lid wetting?

The interplay of several factors that influence on the mixing motion has been optimized, in particular: The minimization of vertical motion, the operating smoothness and as well as the sturdy plate/tube holders. All serve to prevent any uncontrolled, chaotic movement and thus ensure an optimum transfer of mixing energy from the device to the sample. Still, the risk of any lid wetting is dependent on outside factors such as tube size, chosen mixing speed, filling volume and the properties of the sample material (e.g., buffer composition, viscosity, density), etc. To easily configure your optimum mixing parameters despite such variations, MixMate is equipped with five preprogrammed soft keys to enable fast and controlled mixing of various plate and tube formats in standard applications.

Why does the vortexer continue to run for approx. 2 seconds after relieving pressure on the vortex mat?

This 2-second overrun makes the vortexing process more ergonomic, because the vortex mat need not be pressed continuously to keep the vortexer running. It also eases the process of performing vortexing in several tubes successively.

text.skipToContent text.skipToNavigation

CN | CNY

未找到任何结果

搜索建议

产品系列

Show all Product Families ()

文章

Show all Articles ()

内容

Show all Content ()

MixMate^®

Q: Can MixMate be used in automated systems or integrate into an automated pipetting system?

No, because MixMate is not equipped with an interface.

Q: Can I program MixMate to run different mixing steps sequentially?

No. MixMate is not programmable.

Q: Is MixMate able to heat or cool samples?

No, MixMate is a mixing device. For tempering (heating, cooling) of plates or tubes we recommend the Eppendorf Thermomixers or Eppendorf ThermoStat plus.

Q: Can MixMate be operated in an incubator at 37°C?

Yes, MixMate can be operated at ambient temperatures of 2 – 40°C and a relative air humidity of 10 – 75 %.

Eppendorf MixMate mixer device with red PCR 384-well plate

Eppendorf MixMate Tube holder for 0.5 mL lab vessels for sufficient mixing

Eppendorf MixMate Tube holder PCR 96 for mixing PCR plates

Eppendorf MixMate Tube holder for 1.5/2.0 mL lab vessels

Eppendorf MixMate Tube Holder for 5/15 mL lab vessels, filled with 5 mL tubes

Eppendorf MixMate Tube Holder for 5/15 mL lab vessels, filled with 15 mL conical tubes

Eppendorf MixMate Tube Holder for mixing 25/ 50 mL lab tubes

Eppendorf ThermoMixer and MixMate family

Scientist puts plate on Eppendorf MixMate to mix samples

Lab scientist changes settings of Eppendorf MixMate instrument

Eppendorf mixing of small volume samples in the lab

Eppendorf MixMate with PCR 96 tubeholder

Eppendorf Mixmate with semi-skirted PCR plate

Eppendorf MixMate mixing instrument to mix or vortex lab samples

产品信息

需要直线混合？ 3 合 1 模块：混匀工作板和微量管，并具有涡旋振荡混匀功能。这款高速混匀设备确保不同试管或板内样品的充分混匀。优越的 ^2DMix-Control 混匀操控技术进行可控的混匀，防止溅射。

显示更多产品信息

了解更多有关Eppendorf产品的可持续特性，包括如何辨别可持续混匀仪

索取演示版

您可以在以下网址找到其他下载资料本页面底部

产品信息

技术数据

用途

特征

需要直线混合？ 在几秒钟内充分和可靠地混匀您的样品。无论是微孔板（96 或 384 孔）还是样品管，都将将以最佳方式处理您的样品。集成人体工程学涡旋功能，MixMate 是您的完美实验室助手。具有 2 秒振荡延迟功能，可进行连续混匀，无需重新启动。

经常无法获得满意的混匀结果？

可靠的样品混匀，其意义已远远超出混匀本身，尤其是微升级样品。数十年来，我们一直致力于为客户提供混匀设备，并探索出一条能够进一步提升微升级样品可靠混匀性能的方法：

^2DMix–Control

卓越的 ^2DMix–Control 技术，在受控和循环运动下混合液体。轨道偏心距 3 mm，最高转速 3,000 rpm：可以获得绝佳混匀性能，即使是棘手样品也可轻松处理。 MixMate 混匀小精灵具备足够的混匀能力，来应对各种高挑战性的混匀实验。无论样品管形状或样品属性如何，大多数样品都能在 1 分钟内有效地混匀。

需要小体积混匀？

使用 MixMate 进行受控混合的缩时摄影。卓越的 ^2DMix‐Control 技术，在极度受控和循环运动下混合液体。不存在溅液，从而可以在混合过程中避免罐盖潮湿或交叉污染。

手头有不同样品?

MixMate提供足够的混合动力以应对挑战性的混合任务。无论样品管形状或样品属性如何，大多数样品都能在 1 分钟内有效地混匀。更多信息见应用文献第130期。

需要使用不同尺寸的样品管？

MixMate 混匀小精灵可以配备不同的管架，灵活用于常见样品管和工作板。
通过快速更换功能可以快速方便地更换管架。

早已厌倦纸质记录？

eLabJournal Electronic Lab Notebook 为记录和追踪研究数据（诸如 MixMate 相关工作流程）提供了直观且灵活的解决方案。提高记录、组织、搜索和归档所收集数据的效率。通过免费的eLabJournal附加组件，您可将eLabJournal的功能扩展到一个完全集成的Laboratory Information Management System。

免费试用 30 天！
访问www.eLabJournal.com

阅读更少

规格	MixMate^®

样品容量	最大 96 × 0.2 mL PCR管, 24 × 0.5 mL 离心管, 24 × 1.5 mL 离心管, 24 × 2.0 mL 离心管, 8 × 5/15 mL, 4 × 25/50 mL, 1 × DWP/MTP 或 1 × PCR板
产品类型	Mixer混匀仪
定时器	可连续运行 15 秒 – 99.3 小时
噪音水平	<50 dB(A)
电源	230 V, 50 – 60 Hz
最大能耗	40 W
尺寸（长x宽x高）	17.0 × 23.0 × 13.0 cm / 6.7 × 9.1 × 5.1 in
产品重量	4.2 kg / 9.2 lb
最大速度	3,000 rpm
混匀频率	300 – 3,000 rpm
混合和漩涡半径	1.5 mm
接触回旋频率	3500 rpm
振幅	3 mm