Does the Centrifuge 58xx R has an energy saving function?

Yes, the ECO shut-off automatically switchs off the compressor after 8 hours of non-use. The device has a stand-by button.

How many times can aluminum rotors be autoclaved?

Aluminum rotors can be autoclaved up to 100 times for 20 minutes at 121 °C.

The Centrifuges 5804/ 5804 R and 5810/ 5810 R are programmable. What is saved during the programming?

All data is saved that can also be entered manually, such as rotational speed or RCF, maximum radius, run time, acceleration and braking ramps, "at set rpm", temperature.

Do the adapters for the 0.2/ 0.4/ 0.5/ 0.6 mL tubes, which are designed for the rotors F-45-30-11 and FA-45-30-11, also fit into the rotor F-34-6-38 with the adapter 5804 770.005 (for 1.5/ 2.0 mL tubes)?

Yes, these adapters can also be used in the rotor F-34-6-38 with the adapter 5804770005.

Is it possible to centrifuge 50 mL and 15 mL tubes together in one rotor?

Yes, it is possible, provided that the rotor is loaded symmetrically. This means that the 50 mL tubes and the 15 mL tubes are positioned opposite one another and are positioned symmetrically. Please use the appropriate adapters for the tubes.

Can 4 microplate buckets (order number 5810702003) be fitted into the rotor A-4-62 (5810709008) of Centrifuge 5810 / 5810 R?

Yes. It is the same rotor cross. Please note that mixed loading of the rotor with rectangular buckets and MTP buckets is not permitted.

There are 2 different adapters for the 15 mL tubes. One for tubes with round bottoms and one with a conical bottom for conical tubes. Can I not use one adapter for both tubes?

No, unfortunately this is not possible. In order to be able to reach the high rotational speeds, the adapters must be form-locking.

Can the new rotor generation be used with older Centrifuges without retrofitting?

Yes, you can use the new rotors from software version 8.4 onwards. From versionb 7.0 on a software update to version 8.4 can easily be performed by trained service technician. In case of older software versions, the complete PCB control/frequency converter must be replaced. You can see the current software version of your centrifuge briefly on the display after switching it on.

Is it possible to adjust the Centrifuge 5804/ 5804 R or 5810/ 5810 R so that it stops on its own, meaning without active braking?

Yes. Free deceleration of your centrifuge can be achieved by setting the braking level to 0.

Is it possible, in addition to 25 cm2 flasks, to use 75 cm2 flasks also?

Only a limited choice of 72 cm2 flasks are possible to be centrifuged: We recommend to use Saarstedt flasks (Article number 831811-002) with the cell culture flask adapter (Article number 5825719000) in combination with rotor A-4-81-MTP/Flex or A-4-62-MTP and Centrifuge 5810/ R.

Is there an adapter to spin microscope slides in centrifuge 5804 / 5804 R / 5810 / 5810 R?

Up to 12 slides can be inserted into the CombiSlide adapter 5825706005 and then centrifuged in the swing out rotors of Centrifuge 5804/ 5804 R or 5810/ 5810 R.

How can I recognize in the display of the Centrifuges 5804/ 5804 R or 5810/ 5810 R whether I have selected "rpm" or "rcf"?

For rcf, a "*" is displayed in front of the value. rpm is not indicated by a symbol.

How are the Centrifuges 5804/ 5804 R and 5810/ 5810 R protected during transport? Is there a transport protection device?

No, the Centrifuges 5804/ 5804 R and 5810/ 5810 R do not come with a transport protection device. They are packaged in polystyrene for protection. Because the rotor is not in the centrifuge during transport, there are no movable parts to make a transport protection device necessary.

How big is the g-force difference between the lowest and the highest plate when loading a bucket of the rotor A-2-DWP with four microplates?

The following g-forces are reached with the rotor A-2-DWP: Lowest plate: 2,250 x g Highest plate: 1,825 x g

Can I still change the settings when I have started the Centrifuges 5804/ 5804 R or 5810/ 5810 R?

Yes, the speed, the time and the temperature can be changed even when the centrifuge is running. To do this, please press the SPEED, TIME or TEMP key and change the values by pressing the arrow keys.

How does the Centrifuge recognize that a different rotor is in use?

A new rotor automatically will be recognized as soon as it starts moving. Moving and recognition of the rotor can be performed manually by making it spin counterclockwise (roughly 200 rpm necessary), or by turning the Centrifuge on. As soon as the rotor starts spinning it will be recognized. When indicated, the Centrifuge shuts down under specification of max. speed in case the indicated max. speed of the previous rotor was higher. In this case the Centrifuge must be restarted.

What is the minimum rotational speed (rpm) of the Centrifuge 5804/ 5804 R or 5810/ 5810 R, and in which increments can it be increased?

The minimum rotational speed is 200 rpm, irrespective of the inserted rotor. The minimum rotational speed can be increased in increments of 10 rpm up to 5,000 rpm and then in increments of 100 rpm.

What is the meaning of the red knob on the rotor lid?

A fixed-angle rotor with a red knob on the rotor lid indicates aerosol-tightness.

Do the adapters for the 0.5 mL tubes fit into the rack for 1.5/ 2.0 mL tubes of the rotor T-60-11 for centrifuge 58xx?

Yes, the adapters can be inserted into the rotor for centrifugation of 0.5 mL tubes.

"Clean rotor" appears on the display of my centrifuge. Do I now need to remove the rotor from the centrifuge, and, if yes, how?

This display appears every 200 centrifugation runs. For cleaning the rotor and the rotor chamber, the rotor must first be removed from the centrifuge. To do this, loosen the rotor nut by turning it counter-clockwise with the supplied rotor key. Please clean the rotor and rotor chamber only with mild cleaning agents (e.g. 70% alcohol solutions or commercially available alcoholic disinfectants).

Is it possible to switch off the brakes of Centrifuges 5804/ 5804 R or 5810/ 5810 R, e.g. when centrifuging a gradient?

Yes. Free deceleration of your centrifuge can be achieved by setting the braking level to 0.

Can rotor A-4-81 or S-4-104 be operated with rectangular buckets and MTP / Flex buckets?

Yes, this so-called mixed loading is possible. Please ensure that the same type of buckets are always used in opposing positions.

In which rotor is it possible to centrifuge 50 mL DIN glass tubes?

50 mL DIN glass tubes (diameter 34 mm, length 100 mm) can be centrifuged in the adapter for 50 - 75 ml tubes (order number 5804 760.000) of the swing-bucket rotor A-4-44 or adapter 5810 760.003 of swing-bucket rotor A-4-62 . Depending on the length of the tube, the uppermost module of the adapter can be removed for centrifugation of 50 mL DIN glass tubes.

How does the Centrifuge 58xx and 59xx recognize that a different rotor is in use?

A new rotor will automatically be recognized as soon as it starts spinning. Recognition of the rotor can be performed manually by making it spin counterclockwise (roughly 200 rpm necessary), or by turning the Centrifuge on. As soon as the rotor starts spinning it will be recognized. In case the indicated max. speed of the previous rotor was higher, speed must be confirmed in a display pop-up. The user has the choice between the rotor-specific max. speed or a lower speed, that can be set directly.

Millipore offers centrifugation filter tubes (Centripreps). Can these tubes be centrifuged in a rotor of the Centrifuge 5810/5810 R?

Yes, for 50 mL Centripreps we offer the adapter 5810 739.004 for the rotor A-4-81.

The writing on one rotor of the Centrifuge 5804/ 5804 R or 5810/ 5810 R says, for example, "6x125g". Does this mean that the centrifuge only enables an RCF of 125 or that it can only be loaded with a maximum of 6 times 125 gram?

This label states that the rotor can be loaded with a maximum of 6 x 125 gram. "g" is the official abbreviation for "gram". Where "g" is used as an abbreviation of "g-force", the number and "x g" are used. Example: 10,800 x g.

Does Eppendorf offer a rotor for PCR strips for Centrifuges 5804/ 5804 R or 5810/ 5810 R?

The PCR strip rotor F-45-48-PCR is available under the order number 5804 735.005. It can centrifuge up to 6 x 8-well strips at 12,000 rpm / 15,350 x g.

For which centrifuge can we use our mobile tables 5921 000 010 and 5921 000 012?

The mobile tables can be used for centrifuges 59xx as well as 58xx.

离心机维护服务价格？

费用取决于型号和所执行的维护。请联系您当地的 Eppendorf 客服。

离心结束后，是否应该盖上冷冻离心机盖？

如果经常在低温下使用离心机，您应该盖上冷冻离心机盖。不使用时（例如夜间），请关掉离心机并清洁转子腔。离心机盖应保持打开状态以干燥离心机。

为什么要定期维护离心机？

为了确保设备的最优性能和精确度。这也能早期发现任何缺陷，然后可以很容易地纠正。执行大量离心任务会增加转子损坏的可能性。通过正规检查，可以在早期阶段检查出任何损坏，也就是说，可以在转子发生任何严重损坏之前更换。

转子检查是维护服务的一部分吗？

不是。可以在维护服务之外单独订购，具体取决于转子类型（固定角转子或水平转子）。

请联系您当地的 Eppendorf 服务团队。您可以在我们的主页或资讯材料中找到联系信息。

怎么样清洁离心机？

请使用中性清洁剂进行清洁。我们建议使用乙醇或醇类消毒剂进行消毒。请确保在选择消毒方法时遵守适用的法律法规和准则。您可以观看视频“Centrifuge Maintenance - The basis for your lab safety”（离心机维护 - 实验室安全的基础）或从我们的网站下载操作手册了解详细信息。

我想提高我的技能，你们能够提供哪些类型的培训或在线培训？

请访问 Eppendorf 网页关于 Eppendorf 培训中心的信息或联系您当地的 Eppendorf 客服，以获取更多信息和报价。

我可以自己进行软件更新吗？

编号对于带 USB 接口的离心机，应由有资质的 Eppendorf 维护技术人员通过现有 USB 端口进行软件更新。这样才能确保实现最新的安全要素、对转子进行最新检测并且通过最新参数优化机器运行。

离心机需要多久维护一次？

这取决于使用强度，并且因设备负载而异。然而，建议每年至少维护离心机一次。

IQ 或 OQ 是什么？有什么用？

安装和操作验证；IQ 记录设备已正确交付和安装。 OQ 检查设备是否正常运行。 IQ/OQ 确保设备满足您的质量管理要求，确保设备正常运行且符合制造商指标。

离心机需要多长时间进行一次 OQ？

公司负责对设备进行技术检查。 Eppendorf 建议定期进行设备验证，具体取决于使用强度。然而，至少应每年进行一次 OQ。

进行维护之前，需要我怎么样处理设备？

首先需要清除设备污染。设备不得锁定且所有样品已从设备中移除。

text.skipToContent text.skipToNavigation

CN | CNY

未找到任何结果

搜索建议

产品系列

Show all Product Families ()

文章

Show all Articles ()

内容

Show all Content ()

Centrifuge 5810/ 5810 R - 台式离心机

Benchtop Centrifuge 5810 and 5810 R with mixed loading capability for tubes, bottles, and plates

Eppendorf Rotor S-4-104 for benchtop centrifuge Centrifuge 5810/ 5810 R

Eppendorf plate Rotor S-4-104 for benchtop Centrifuge 5810/5810 R

Eppendorf Rotor S-4-104 with Vacutainer for benchtop Centrifuge 5810/5810 R

Rotor S-4-104 with Vacutainer for benchtop centrifuge Centrifuge 5810/5810 R

Eppendorf QuickLock® caps for benchtop centrifuge Centrifuge 5810/5810 R

Centrifuge Rotor FA–45–6–30 with QuickLock® lid mechanism

Eppendorf Rotor FA-45-48-11 with Eppendorf QuickLock® technology

产品信息

Centrifuge 5810/5810 R高速离心机是目前在售的最小的 3 L 台式离心机之一。它非常适合中等到高通量实验室，集多功能性与高容量于一身，可使用离心管和工作板。

显示更多产品信息

索取演示版

您可以在以下网址找到其他下载资料本页面底部

产品 (2)

组合套装 (8)

Services (27)

转子 (22)

附件 (2)

2 产品

Centrifuge 5810

按键式, 非冷冻, 不含转子
230 V/50 – 60 Hz (CN)

更多产品详情...

数量

库存状态

目录编号 5810000092

价格

¥ 103,304.00

查询

Centrifuge 5810 R

按键式, 冷冻型, 不含转子
230 V/50 – 60 Hz (CN)

更多产品详情...

数量

库存状态

目录编号 5811000096

价格

¥ 160,118.00

查询

显示更多产品

已添加到您的购物车

产品信息

技术数据

特征

Centrifuge 5810/5810 R 台式离心机以其可靠品质而闻名，为您提供更具成本效益的解决方案，适用于转速高达 20913 x g（14000 rpm）的中等至高通量应用。这款台式离心机用于每种实验室，具备静音操作、轻触盖锁定功能和低开盖高度，便于装载或者拿取样品，简化日常工作流程。
提供一系列转子和适配器，具备多样卓越功能，可以混合装载多种离心管、试剂瓶和工作板。搭载全新一代转子，Centrifuge 5810/5810 R最大试管容量提升至 4 x 750 mL（或 28 x 50 mL / 56 x 15 mL）。水平转子和适配器适用于 0.2 mL 至 750 mL 离心管和试剂瓶，固定角转适用于 0.2 mL 至 85 mL 离心管。工作板转子可离心所有常见类型的多孔板，如 PCR、细胞培养或深孔板。

Eppendorf 台式离心机Centrifuge 5810/5810 R非常适合中等到高样品通量实验室。

气密性转子盖便于单手操作

Eppendorf QuickLock^®转子盖极大降低操作难度，便于单手操作。您可使用把手将封闭吊篮安全转移至生物安全柜，以便在安全环境中打开。

您是否拥有 Eppendorf 产品？已经注册了？

您知道吗，每款 Eppendorf 注册产品均可在我们的奖励商店兑换以下?
• 100 点 epPoints^®
• 当您注册离心机、振动试验机、CO2 培养箱或循环仪时，可享受额外 3 个月的保修服务
• 每款注册产品均可参加一次 Eppendorf 独家抽奖活动
• 在 Eppendorf 网站上分享您的个人产品故事

操作非常简单！您可以 -
1. 下载 Eppendor f应用程序，扫描并注册，或者
2. 访问我们的网页，登录 myEppendorf 帐户并输入产品序列号
更多信息敬请访问：www.eppendorf.com/productregistration

废弃产品

包装处置
离心机包装包含不同材料，包括木制托盘、纸板、塑料防尘罩和一些泡沫部件。材料的回收变得越来越重要：您知道欧洲几乎回收所有的纸板材料吗？我们的离心机纸板包装含有约 50%的回收材料。请通过收集冰箱纸板包装材料并将其防止在适当的回收容器中，来支持回收有价值原材料的全球可持续发展倡议。对于LD-PE和泡沫制成的塑料防尘罩，我们建议选择可以回收PE材料的专门回收合作伙伴料。建议联系您当地的废物管理公司或设施管理团队，了解适合贵公司的可用回收方案。

仪器处置
我们的离心机可以使用多年。但如果需要更换，我们建议您根据当地要求，妥善处置此类仪器。我们强烈建议您在具有主动制冷仪器方面具有丰富经验的经认证本地回收合作伙伴。“本地”处理可减少运输影响。由于制冷剂需要以安全、可持续的方式进行移除和回收，建议采用“认证”方式对冷却离心机进行处置。

消毒
该设备用于实验室和/或用于处理生物样品。请记住对需要处理的设备进行充分去污。查看当地要求。有关更多信息，请联系当地的生物安全官员和/或废物管理官员。检查您当地的回收合作伙伴是否有特殊说明和/或文件要求。您也可以使用Eppendorf去污表格作为指导。

阅读更少

规格	5810	5810 R

最大 RCF	20913 × g	20913 × g
最大 RCF，带固定角转	20913 × g	20913 × g
最大 RCF，带水平转子	4500 × g	4500 × g
最大 RCF，带工作板转子	3486 × g	3486 × g
速度	200 – 14,000 rpm	200 – 14,000 rpm
产品类型	离心机	离心机
可用转子	18	18
最大容量	4 × 750 mL/4 × 4 MTP	4 × 750 mL/4 × 4 MTP
加速/减速档	10/10	10/10
程序数量	35 个用户自定义程序	35 个用户自定义程序
定时器	1 分钟至99 分钟, 可连续离心，有瞬时离心功能	1 分钟至99 分钟, 可连续离心，有瞬时离心功能
噪音水平	<70 dB(A)	<56 dB(A)
电源	230 V, 50 – 60 Hz	230 V, 50 – 60 Hz
最大能耗	900 W	1650 W
尺寸（长x宽x高）	53.5 × 60.8 × 34.5 cm / 21.1 × 23.9 × 13.6 in	70.0 × 60.8 × 34.5 cm / 27.6 × 23.9 × 13.6 in
占地面积（带/不带前面板的尺寸，WxD）	54 × 54厘米 /  21.1 × 21.1英寸	70 × 54厘米 /  27.6 × 21.1英寸
产品重量	68 kg / 149.9 lb	99 kg / 218.3 lb
开盖高度	80 cm / 31.5 in	80 cm / 31.5 in
冷冻型	非冷冻	冷冻型
温度范围	–	-9 °C 至 40 °C

最大容量
锥形管	56 × 15 mL/ 28 × 50 mL	56 × 15 mL/ 28 × 50 mL
板	16 × MTP/ 2 × DWP	16 × MTP/ 2 × DWP
Blood collection tubes	100 × 13 mm/ 52 × 16 mm	100 × 13 mm/ 52 × 16 mm

噪音水平
FA-45-6-30 气密性固定角转 (6×50 mL)	<56 dB(A)	<55 dB(A)
S-4-104 水平转子(4×750 mL)	<70 dB(A)	<56 dB(A)
S-4-72 水平转子 (4×250 mL)	–	–