I have noticed that more solution is used for reverse pipetting than for normal pipetting. What is the reason for this?

Reverse pipetting means uptake of liquid including the blow-out volume and dispensing of liquid without the blow-out volume. Reverse pipetting is recommended to reduce the error with viscous or foaming liquids or when dispensing very small sample volumes. The excess solution aspirated remains in the tip and is discarded.

Can you recommend any literature on reverse pipetting?

Userguides 20 and 21 describe the technique and give application examples. They can be downloaded from the Knowledge Base on our website.

Should the pipette tip be wetted with liquid before pipetting volumes smaller than 10 µL?

Regardless of the volume, the air cushion should be wetted by multiple filling and emptying of the tip before dispensing.

What is the best way to pipette viscous liquids?

When pipetting viscous liquids, we recommend positive displacement instruments like Biomaster, Multipette/Repeater, and Varipette or an air cushion pipette (Research plus, Reference 2) in combination with the reverse pipetting technique (see Userguide 20 and 21 for details).

Is there an Eppendorf pipette which can be used to pipette 40 % polyethylene glycol 8000 (PEG)?

Yes, for pipetting PEG instruments operating according to the positive displacement principle like the Biomaster or a Multipette/Repeater can be used.

What is the best way to pipette chloroform?

When pipetting chloroform, we recommend positive displacement instruments like Biomaster, Multipette/Repeater, and Varipette or an air cushion pipette (Research plus, Reference 2) in combination with the reverse pipetting technique (see Userguide 20 and 21 for details).

What is the best way to pipette diethyl ether?

Diethyl ether has such a high vapor pressure that it would leak out of the tip immediately when an air cushion pipette is used. For this reason, it can only be pipetted using a positive displacement pipette, such as Biomaster, Multipette/Repeater, and Varipette.

Are Eppendorf pipettes resistant to acetonitrile?

Yes, Eppendorf pipettes are resistant to acetonitrile but care must be taken to avoid damage to printing and display window.

What should be considered when pipetting methanol with air cushion pipettes?

Due to the increased vapor pressure, we recommend that the tip is prewetted at least 3 times and that the reverse pipetting technique is used.

What is the best pipette for pipetting a 99% solution of n-amyl alcohol?

A 99 % solution of n-amyl alcohol is a highly viscous solution. We recommend working with an instrument that operates according to the positive displacement principle like Multipette/Repeater, Varipette, or Biomaster.

What is the best way to dispense organic solvent?

It is best to use a positive displacement device like the Multipette/Repeater. Positive displacement devices are most suitable for precise and drip-free dispensing of liquids with high vapor pressure. As the liquid is enclosed in a tip with integrated piston, the solvent vapor does not come into direct contact with the instrument.

I would like to pipette dichloromethane and n-hexanol very precisely. Can I use air cushion pipettes for this application?

Both dichloromethane and n-hexanol have a very high vapor pressure. For that reason, positive displacement instruments like the Biomaster and the Multipette/Repeater should be used.

Are your pipettes free of nucleic acids?

No, we cannot guarantee this. Of course we work carefully and cleanly in production, but no special measures are taken to prevent the infiltration of nucleic acids. To protect your pipette from contamination, we recommend using positive displacement pipettes, for example, our Biomaster or filtertips (ep Dualfilter T.I.P.S. or ep Dualfilter T.I.P.S. SealMax).

How can radioactive contamination be removed from Eppendorf pipettes?

Following contamination of pipettes with radioactive liquids, we recommend placing the contaminated parts in a complex-forming liquid or special cleaning solution. Then rinse very thoroughly with distilled water and dry. Grease piston lightly afterwards.

Do Eppendorf pipettes always need to be greased?

No, the piston only has to be greased if grease-dissolving solutions like organic solvents have been used.

Can the pipette withstand evacuation (applying a vacuum)?

No, air cushion pipettes should not be used under vacuum, as the pressure ratios are not right.

How should warm or cold liquids be pipetted?

Exactly in the same way as liquids at room temperature, however, please note that solutions may behave differently. In addition, the pipetting accuracy / precision may be outside the permissible error limits. In order to achieve maximum accuracy / precision, all components should have the same temperature: pipette, tips, liquid, and the surrounding air.

Are the handles of Eppendorf pipettes made of a special material to minimize temperature effects during pipetting?

Temperature effects are minimized in our pipettes by their design. We use a special polypropylene which satisfies the special requirements on a pipette handle.

Do Eppendorf pipettes always have to be kept in a stand or can they also be put down on the laboratory bench?

They can be put down on the laboratory bench - but never with a full tip.

I often work with different chemicals. Can you tell me when I need to adjust my pipettes?

This belongs to the permissible errors of your specific application. In general an adjustment of air cushion pipettes, in other words altering the stroke of the pipette, is required for solutions of a density higher 1.2 mg/µL. Please be aware that variable manual pipettes turn into "fixed-volume pipettes" when being adjusted: They can only be adjusted to a specific liquid to one volume and not across the entire dispensing range. Eppendorf manual pipettes have a user adjustment for temporary adjustment purposes. This user adjustment can easily be set back to manufacturer settings without the need for recalibration. For the correct procedure and examples for settings of user adjustments for different liquids please see the operating instructions and CD enclosed to your pipette.

How do I determine the volume values when calibrating gravimetrically?

The measuring values of the analysis scales are multiplied by the correction factor Z (see SOP pipettes). This takes into account the density of the water at the relevant temperature and the relevant air.

What does EN ISO 8655 cover?

ISO 8655 addresses the needs of suppliers, test houses, and users and specifies the general requirements for piston-operated liquid handling devices. It is structured in seven chapters: ISO 8655-1: Terminology, general requirements, and user recommendations ISO 8655-2: Piston pipettes ISO 8655-3: Piston burettes ISO 8655-4: Dilutors ISO 8655-5: Dispensers ISO 8655-6: Gravimetric method for the determination of measurement error ISO 8655-7: Non-gravimetric methods for assessment of equipment performance (titration, photometry)

What do the terms random error and systematic error mean in a pipette calibration?

The systematic error describes the deviation of the dispensed volume from the nominal volume or from the selected volume of the piston stroke device, and is determined by establishing the mean value of (usually) 10 measurements. The random error describes the mean variation of the dispensed volumes from the mean value of the dispensed volumes, and is determined by calculating the repeat standard deviation of (usually) 10 measurements.

Why are the Z factors listed in our SOP different from factors which can be derived from density reference values (of water)?

The Z factor is included in EN ISO 8655-6 and was incorporated into our SOP. As we understand it, it was incorporated in the standard by the Physikalisch Technische Bundesanstalt in Braunschweig. The Z factor describes the density of water at a particular temperature using a 5th degree polynomial. Furthermore, the density of water is corrected by the density of air (derived from air pressure) and a fixed correction value for balances. These corrections are the key reasons for the deviation from density values in various books of tables.

At which volumes should a variable pipette be calibrated?

According to the EN ISO 8655 standard, a variable pipette should be calibrated to 3 volumes during conformity testing: 1. Nominal volume, 2. 50 % of nominal volume, 3. Smallest value that can be set or 10 % of nominal volume.

What is the nominal volume of a variable pipette?

The nominal volume of a variable pipette is always the maximum volume. For a 100 - 1,000 µL pipette, it is therefore 1,000 µL.

I very frequently work with different chemicals. Can I still perform pipette calibration using water?

Calibration, i.e. checking a pipette on a balance, is always performed using distilled or deionized water (see EN ISO 8655).

During weighing (pipette calibration) I obtained steadily decreasing measuring results. Why is this?

The weight fluctuations you measured would appear to be a temperature problem. Please ensure that the pipette, the distilled water used for testing, the tips etc. are all at the same temperature. It is recommended that the pipettes be placed in the weighing room at least 2 hours before the test is performed. While measuring, ensure that transfer of heat from your hands is kept to a minimum (otherwise weight fluctuations may occur!) Tip: do not constantly grasp the pipette in the palm of your hand while waiting for each measurement result! We recommend our standard operating procedure (SOP) for pipettes as a source of basic information on pipette calibration.

How are multi-channel pipettes tested?

According to ISO 8655, all channels of multi-channel pipettes are to be tested. All channels have to be filled but only the channel to be tested is measured. Because of the high number of measurements (8-channel pipette: 240 measurements, 12-channel pipette: 360 measurements), it makes sense to send the multi-channel pipette to a professional calibration lab. These labs have special constructions for balances to ensure that all channels are filled but only one channel is measured.

Is the pipette grease free of resins?

Yes, the pipette grease supplied by Eppendorf is free of resins.

How is the wall mount for pipettes attached to the wall?

The pipette holder is affixed to the wall with adhesive.

Can the Xplorer be autoclaved, and how often?

The lower part of the Xplorer can be autoclaved. 175 autoclaving cycles (121 °C, 1 bar, 20 min.) were tested. This number of tests corresponds to the average use over 5 years.

Is the Xplorer resistant to solvents?

Yes, the Xplorer is resistant to solvents. Only the display shall not come into contact with the solvent.

Can the Xplorer be readjusted?

Yes, there are several options for adjusting the pipette in the ""Options"" operating mode, e.g. to 75 % ethanol, altitude, elongated tips. Furthermore, individual adjustments are possible, as 1-point, 2-point or 3-point settings.

Which volumes are used for mixing in the mode "Pipetting and mixing"?

In the "Pipetting and mixing" operating mode, the mixing volume can be defined independently from the filling volume.

Can the acoustic feedback of the Xplorer be turned off?

Yes, the volume of the acoustic feedback can be set to levels 0-8 in the "Options" operating mode.

How can accidental parameter changes be prevented?

A complete run with volume, speed, etc. can be saved at the program level. After exiting the program level, the run can no longer be changed just by pressing the keys. Additionally, the Xplorer plus offers possibilities of protecting settings by password.

Various speeds can be selected with the Xplorer. What speeds do the settings 1-8 represent?

This is depending on the aspiration volume. Please see operating manual in case of further questions.

How long does it take the Xplorer to aspirate 10 ml?

Depending on the speed level, the Xplorer pipette needs for aspiration of 10 mL between 12 s (Step 1) and 2.6 s (Step 8).

Are the Xplorer and Xplorer plus resistant against UV-light?

The Xplorer is UV-resistant. Longer periods of irradiation can lead to very minimal material discoloration that does not have any effect on functionality.

Does the technical data also apply to the "Dispensing" operating mode?

The Xplorer technical data is only valid for pipetting. Conformity must be achieved for this operating mode. For piston stroke pipettes, there are no requirements for dispensing accuracy according to EN ISO 8655.

Can the aspiration volume be limited?

Yes, a volume limit can be defined in the "Options" operating mode.

What charging possibilities are available for the Xplorer?

The Xplorer can be charged using the power supply included in the accessories or in the charging stand or charging carousel (optional accessories). One Xplorer can be charged in the charging stand and four in the charging carousel. A single-channel or multi-channel Xplorer can be attached to a charging shell.

Can the Xplorer also be charged in Multipette charging stands?

No, the Xplorer cannot be charged in the Multipette charging stand. But the charging shells of the Xplorer charging stand can be exchanged. A charging shell for a Multipette stream/Xstream can be used instead of a charging shell for an Xplorer.

How long is the service life of the battery?

The lithium polymer battery features high energy density. Its service life is several years; but this is strongly dependent on usage and storage conditions.

Can the battery be reordered?

Yes, batteries for electronic liquid handling can be ordered separately as spare parts and should be replaced after approx. 3 years of use.

Which pipette tips fit on the Xplorer?

The certificate of conformity for the Eppendorf Xplorer ® system is valid for epTIPS. However, the Xplorer can also be used with common competitor tips.

Is it possible to mix liquids in the micro test plate or small volumes with the preparation?

In the operating mode "Pipetting and Mixing," the sample is automatically mixed with the preparation after dispensing. The mixing cycles and mixing volume can be individually defined for this.

Can I precisely dispense liquids such as ethanol or glycerol with the Xplorer?

On the Xplorer, the pipette can be adjusted to different liquids or geographic heights using 1, 2 or 3-point adjustment, taking into account the corresponding density and associated scale results. The setting for ethanol 75 %25 or glycerol 50 %25 is completed using an internally determined factor that takes into account the density.

When pipetting foaming liquids (e.g. cell culture media) I‘m transferring foam which got trapped between the epT.I.PS. 384. How can I improve?

When pipetting foaming liquids it may happen that foam adhere between the tips. Make sure to pipette slowly avoiding foam formation. Importantly, do not immerse the tip too deeply into the liquid preventing foam getting caught between the tips.

How often should pipettes be calibrated?

The user decides upon the frequency of calibration, the number of test volumes and the number of measurements for each test volume within the framework of monitoring his test materials. This can vary depending on the frequency of use of the pipette, the number of users of the device, the aggressiveness of the liquids to be dispensed and the error limits deemed acceptable by the user. However, an inspection should be carried out at least once a year. See also EN ISO 8655-6.

text.skipToContent text.skipToNavigation

메뉴

KR | KRW

국가 설정 선택

* = 필수

국가 선택 *

(중국) 대만
(중국) 홍콩
가나
가봉
가이아나
감비아
건지
과들루프
과테말라
그레나다
그리스
그린란드
기니
기니비사우
나미비아
나우루
나이지리아
남아프리카공화국
네덜란드
네팔
노르웨이
노퍽 섬
뉴질랜드
뉴칼레도니아
니우에
니제르
니카라과
덴마크
도미니카
도미니카공화국
독일
동티모르
라오스 인민민주공화국
라이베리아
라트비아
레바논
레소토
레위니옹
루마니아
룩셈부르크
르완다
리비아
리투아니아
리히텐슈타인
마다가스카르
마르티니크
마셜 제도
마요트
말라위
말레이시아
말리
맨섬
멕시코
모나코
모로코
모리셔스
모리타니
모잠비크
몬세라트
몬테네그로
몰도바
몰디브
몰타
몽골
미국
미얀마
미크로네시아 연방
바누아투
바레인
바베이도스
바하마
방글라데시
버뮤다
베냉
베네수엘라
베트남
벨기에
벨리즈
보스니아헤르체고비나
보츠나와
볼리비아
부룬디
부르키나 파소
부탄
북마케도니아
불가리아
브라질
브루나이 다루살람
사모아
사우디아라비아
산마리노
상투메프린시페
생바르텔르미
서사하라
세네갈
세르비아
세이셸
세인트 마틴(프랑스령)
세인트루시아
세인트빈센트그레나딘
세인트키츠네비스
소말리아
솔로몬 제도
수리남
스리랑카
스와질랜드
스웨덴
스위스
스페인
슬로바키아
슬로베니아
시에라리온
신트마르턴(네덜란드령)
싱가포르
아랍에미리트
아루바
아르메니아
아르헨티나
아이슬란드
아이티
아일랜드
아제르바이잔
아프가니스탄
알바니아
알제리
앙골라
앤티가바부다
앵귈라
에리트레아
에스토니아
에콰도르
에티오피아
엘살바도르
영국
영국령 버진 아일랜드
예맨
오만
오스트레일리아
오스트리아
온두라스
요르단
우간다
우루과이
우즈베키스탄
우크라이나
이라크
이스라엘
이집트
이탈리아
인도
인도네시아
일본
자메이카
잠비아
저지
적도 기니
조지아
중국
중앙아프리카공화국
지부티
지브롤터
짐바브웨
차드
체코
칠레
카메룬
카보베르데
카자흐스탄
카타르
캄보디아
캐나다
케냐
케이맨 제도
코모로
코소보
코스타리카
코코스(킬링) 제도
코트디부아르
콜롬비아
콩고
콩고민주공화국
쿠웨이트
쿡 제도
퀴라소
크로아티아
크리스마스 섬
키르기스스탄
키리바시
키프로스
타지키스탄
탄자니아
태국
터크스 케이커스
터키
토고
토켈라우
통가
투르크메니스탄
투발루
튀니지
트리니다드토바고
파나마
파라과이
파키스탄
파푸아 뉴기니
팔라우
팔레스타인 지역
페로 제도
페루
포르투갈
포클랜드 제도
폴란드
프랑스
프랑스령 기아나
프랑스령 폴리네시아
피지
핀란드
필리핀
핏케언
한국
헝가리
활리스 퓌티나

언어 선택 *

한국어

통화 선택 *

새로 변경한 국가의 웹사이트에서 귀하의 장바구니가 복원되지 않으며, 이 국가의 웹사이트를 재방문할 경우에도 장바구니는 복원되지 않습니다. 장바구니를 저장하려면 로그인하시기 바랍니다.

myEppendorf

빠른 주문

견적

로그인

Lab Academy
Beyond Science
서비스 및 지원
회사 및 직무 소개

Lab Academy
Beyond Science
서비스 및 지원
회사 및 직무 소개

KR | KRW

국가 설정 선택

* = 필수

국가 선택 *

(중국) 대만
(중국) 홍콩
가나
가봉
가이아나
감비아
건지
과들루프
과테말라
그레나다
그리스
그린란드
기니
기니비사우
나미비아
나우루
나이지리아
남아프리카공화국
네덜란드
네팔
노르웨이
노퍽 섬
뉴질랜드
뉴칼레도니아
니우에
니제르
니카라과
덴마크
도미니카
도미니카공화국
독일
동티모르
라오스 인민민주공화국
라이베리아
라트비아
레바논
레소토
레위니옹
루마니아
룩셈부르크
르완다
리비아
리투아니아
리히텐슈타인
마다가스카르
마르티니크
마셜 제도
마요트
말라위
말레이시아
말리
맨섬
멕시코
모나코
모로코
모리셔스
모리타니
모잠비크
몬세라트
몬테네그로
몰도바
몰디브
몰타
몽골
미국
미얀마
미크로네시아 연방
바누아투
바레인
바베이도스
바하마
방글라데시
버뮤다
베냉
베네수엘라
베트남
벨기에
벨리즈
보스니아헤르체고비나
보츠나와
볼리비아
부룬디
부르키나 파소
부탄
북마케도니아
불가리아
브라질
브루나이 다루살람
사모아
사우디아라비아
산마리노
상투메프린시페
생바르텔르미
서사하라
세네갈
세르비아
세이셸
세인트 마틴(프랑스령)
세인트루시아
세인트빈센트그레나딘
세인트키츠네비스
소말리아
솔로몬 제도
수리남
스리랑카
스와질랜드
스웨덴
스위스
스페인
슬로바키아
슬로베니아
시에라리온
신트마르턴(네덜란드령)
싱가포르
아랍에미리트
아루바
아르메니아
아르헨티나
아이슬란드
아이티
아일랜드
아제르바이잔
아프가니스탄
알바니아
알제리
앙골라
앤티가바부다
앵귈라
에리트레아
에스토니아
에콰도르
에티오피아
엘살바도르
영국
영국령 버진 아일랜드
예맨
오만
오스트레일리아
오스트리아
온두라스
요르단
우간다
우루과이
우즈베키스탄
우크라이나
이라크
이스라엘
이집트
이탈리아
인도
인도네시아
일본
자메이카
잠비아
저지
적도 기니
조지아
중국
중앙아프리카공화국
지부티
지브롤터
짐바브웨
차드
체코
칠레
카메룬
카보베르데
카자흐스탄
카타르
캄보디아
캐나다
케냐
케이맨 제도
코모로
코소보
코스타리카
코코스(킬링) 제도
코트디부아르
콜롬비아
콩고
콩고민주공화국
쿠웨이트
쿡 제도
퀴라소
크로아티아
크리스마스 섬
키르기스스탄
키리바시
키프로스
타지키스탄
탄자니아
태국
터크스 케이커스
터키
토고
토켈라우
통가
투르크메니스탄
투발루
튀니지
트리니다드토바고
파나마
파라과이
파키스탄
파푸아 뉴기니
팔라우
팔레스타인 지역
페로 제도
페루
포르투갈
포클랜드 제도
폴란드
프랑스
프랑스령 기아나
프랑스령 폴리네시아
피지
핀란드
필리핀
핏케언
한국
헝가리
활리스 퓌티나

언어 선택 *

한국어

통화 선택 *

자동 피펫팅
자동 피펫팅
바이오프로세스
바이오프로세스
Cell Incubation
Cell Incubation
원심분리기
원심분리기
Cold Storage
Cold Storage
Digital Lab Management
Digital Lab Management
- 기기 관리 소프트웨어
- 시료 및 정보 관리
실험실 소모품
실험실 소모품
Lab Shakers
Lab Shakers
Liquid Handling
Liquid Handling
PCR
PCR
광도 측정
광도 측정
Services
Services
온도 제어 및 Mixing
온도 제어 및 Mixing
- 액세서리
- 장비
프로모션
OEM

myEppendorf

epPoints®
제품 등록
- 제품 등록
주문 내역
- 정기 주문
- VisioNize 구독
견적 적용
목록
- 대량 주문
내 프로필
계정 비활성화

결과 없음

검색 제안

제품군

모든 제품군 표시 ()

기사

모든 기사 표시 ()

콘텐츠

모든 콘텐츠 표시 ()

홈
Products
Liquid Handling
매뉴얼 피펫팅 및 디스펜싱
Eppendorf Xplorer^®/ Eppendorf Xplorer^® plus

Eppendorf Xplorer^®/ Eppendorf Xplorer^® plus - 전자피펫

Eppendorf Xplorer® / Xplorer plus single- and multi-channel electronic pipettes

Eppendorf Xplorer® plus electronic single-channel pipette

Eppendorf Xplorer® plus electronic pipette display and multi-function rocker

Eppendorf Xplorer® (plus) multi-channel electronic pipettes speed up your applications with microplates

Eppendorf Xplorer® plus 16 and 24-channel electronic pipettes are ideal to fill 384-well plates

Fill 384-well plates with ease using Eppendorf multi-channel pipettes with 16 or 24 channels

The Pipette Carousel 2 with Eppendorf Xplorer® electronic pipettes

Discover the smooth handling of Eppendorf Xplorer® pipettes yourself

Female scientist using Eppendorf Xplorer® plus electronic pipette to fill an Eppendorf Tube®

Man using Eppendorf Xplorer® plus 24-channel pipette to fill a 384-well plate

Eppendorf Xplorer® electronic single-channel pipette used to fill an Eppendorf Tube® in the lab

The software of your Eppendorf Xplorer® plus pipette can easily be updated using the Pipette Software Update Tool

ACT label of sustainability certification for Eppendorf Xplorer® plus pipette, 100-1000 µL (blue), single-channel

쿠키가 거부되어 동영상이 로드되지 않습니다. 변경

신규

제품 정보

매일 100 % 최선을 다하는 사람은 최고의 도구와 장비를 가질 자격이 있습니다. Eppendorf Xplorer 및 Xplorer plus 전자식 피펫은 1채널 및 멀티 채널(8채널, 12채널, 16채널, 24채널) 전자 피펫이며, 매뉴얼 피펫팅의 오류 위험을 줄이면서 0.5 ~10 ml의 시료 용량을 흡입 및 분주할 수 있는 제품입니다. Eppendorf XplorerXplorer plus 전자식 피펫은 업무에 새로운 차원의 단순성, 정밀성 그리고 재현성을 제공합니다.

제품 정보 자세히 표시